ifconfig

  linux中对网卡进行编辑的命令.
  无论是Linux 自动安装还是我们手工安装,Linux 都会向你询问有关网络的问题并配置相关的软件。这个用于配置网卡的基本命令就是ifconfig。
  在执行ifconfig 命令后,系统将在内核表中设置必要的参数,这样Linux 就知道如何与网络上的网卡通信。ifconfig 命令有以下两种格式:
  ※ifconfig [interface]
  ※ifconfig interface [aftype] option | address …
  ifconfig 的第一种格式(或使用不带任何参数的ifconfig 命令)可以用来查看当前系统的网络配置情况。
  在刚刚安装完系统之后,实际上是在没有网卡或者网络连接的情况下使用Linux,但通过ifconfig 可以使用回绕方式工作,使计算机认为自己工作在网络上。
  现在我们运行一下ifconfig 命令,不带参数的ifconfig 命令可以显示当前启动的网络接口,其输出结果为:
  [root@machine1 /sbin]#ifconfig
  eth0 Link encap:Ethernet Hwaddr 52:54:AB:DD:6F:61
  inet addr:210.34.6.89 Bcast:210.34.6.127 Mask:255.255.255.128
  UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
  RX packets:46299 errors:0 dropped:0 overruns:0 frame:189
  TX packets:3057 errors:0 dropped:0 overruns:0 carrier:0
  collisions:0 txqueuelen:100
  Interrupt:5 Base address:0xece0
  lo Link encap:Local Loopback
  inet addr:127.0.0.1 Mask:255.0.0.0
  UP LOOPBACK RUNNING MTU:3924 Metric:1
  RX packets:44 errors:0 dropped:0 overruns:0 frame:0
  TX packets:44 errors:0 dropped:0 overruns:0 carrier:0
  collisions:0 txqueuelen:0
  其中以eth0 为首的部分是本机的以太网卡配置参数,这里显示了网卡在下的设备名/dev/eth0 和硬件的MAC 地址52:54:AB:DD:6F:61,MAC 地址是生产厂家定的,每个网卡拥有的唯一地址。
  不过我们可以手工改动网卡的MAC 地址,只要我们在/etc/rc.d/init.d/中的network 中加入:
  ifconfig eth0 hw ether xx:xx:xx:xx:xx:xx
  Jiania 解说注:
  eth0,eth1,eth2,代表网卡一,网卡二,网卡三
  hw 代表hardware 硬件意思
  ether 代表ethernet 以太网的意思
  然后重启,此时再用ifconfig 命令查看一下,我们就会发现网卡的MAC 地址已经变成xx:xx:xx:xx:xx:xx了。
  后继 常用网卡ip设置方法:
  直接通过setup 进行设置。
  配置多个网卡 ifconfig -a 查看网络设备 eth0 / eth1 / lo (回路)。
  ifconfig eth1 //设备1
  ifconfig eth1 192.168.1.10 netmask 255.255.255.0 //设置网卡子网及ip
  man ifconfig
  ifconfig --help(T002)
  命令

自定义分类:
linux网卡
 
贡献者:
itisac
Copyright © 1999-2024 C114 All Rights Reserved | 联系我们 | 沪ICP备12002291号-4